How to Roll a Heart Joint

heart joints killerbongs


The heart joint I am showing you today is a bit different from the most hard joints this heart joint has a joint cone in the middle  witch makes arches of the heart are attached. It can be made without the center cone,  it is up to you what you like. Lets get started 

Step 1: Supplies & Preparation 
Suplplies:
Preperation:

The main cone will need one king sized paper. The two arching joints will each need two or two and a half king sized papers. Either tear or cut lots of glue strips from your rolling papers, you will need many. Grind up your cannabis as evenly as possible- a grinder is the best tool for this process.

Step 2: Roll a Cone
Once we are fully prepared, we can begin by rolling our center cone. If you do not know how to roll a cone please see our cone tutorial. This cone will be rolled tightly, try to eyeball how much ground cannabis is in your center cone and keep that in mind.
Step 3: Prepare to roll the arch joints
Once our center cone is rolled, we can begin on the long arch joints.
The arch joints need to be rolled as straight and evenly as possible, they need to be thin and fairly loose and the length of two king sized papers, try to make sure there is an even amount of cannabis in each of the arch joints. Also, try to make sure that the amount of cannabis that is in the long arch joints is about equal to the amount that is in your center joint.
I have a hard time rolling longer joints, so I require some additional steps. However, if you can easily roll long joints, feel free to skip ahead to Step 8!
Step 4: Roll two thin, straight king sized joints with a filter
Begin by rolling a thin straight joint with one of the king sized papers with a filter.

Then, roll another one exactly like it.
Step 5: roll two thin, straight joints Without filter
Roll two king-sized joints without a filter.
Checkpoint 1
  • 1 cone
  • 2 skinny thin joints with filters
  • 2 skinny thin joints without filters
At this checkpoint, you are done rolling. Congratulations! Now let’s put it all together.
Step 6: Insert joint without filter into tip of joint with filter
Now that our skinny thin joints are rolled we are going to attach them together. We begin by taking one of the skinny joints with filters and inserting one of the skinny joints without filters into its tip.
Step 7: Secure the joints
Using glue strips that we have previously cut we secure these two skinny joints together to create one long joint.
Repeat steps 6&7
Checkpoint 2
Let everything dry before moving to Step 8.
Step 8: Roll arch joints between fingers
Once both of your long arch joints have been rolled, we can begin creating the arches to the heart.
  • Using your thumb and pointer finger, lightly roll the arch joint starting from the middle and working up towards the tip.
Step 9: Lightly pinch and bend the arch joint
Once the top half the of the arch joint is soft you can begin to lightly pinch and bend the tip down towards the filter of the joint.
Repeat this on the other arch joint.
Checkpoint 3
Step 10: Secure tips of arch joints together
Once your arch joints and beginning to look like arches, we can start to attach all the joints together.
  • We can begin at either ends, I am going to start at the tips of the arches.
Wrapping the tips in glue strips, I secure them together and let them dry. Make sure everything is dry before continuing!
Step 11: Secure filters together
One my tips are secured to each other, I begin attaching the filters together.
  • Arrange the filters so that cone in the middle and front and the arches are on either side.
Wrap them with glue strips until they are firmly stuck together. Let dry before continuing.
Step 12: Cover all the holes
Using glue strips I then cover any and all holes that would cause extra airflow.
Step 13: Seriously, cover all the holes
Pull the glue strips between the joints, until all the holes are covered and no air leaks through. Once again, let dry before continuing!
Step 14: Attach the arch tips to the tip of the cone to finish the Heart Joint
Once the holes have all been covered and everything is dry we are almost done!
  • Pull the tips of the two arch joints down to the tip of the main cone.
Make sure everything is solidly attached & let it dry.
We’re finished!
Step 15: (Optional) Decorate the Heart Joint